volume | PIER Journals

Abstract

A novel structure for the capacitive micromachined switches with low actuation voltage is proposed. In this structure both contact plates of the switch are designed as displaceable membranes. Two structures with similar dimensions and conditions, differing on only the number of the displaceable beams are analytically investigated as well as simulated using ANSYS software. The obtained results indicate about 30% reduction in actuation voltage from the conventional single beam to our proposed double beam structure. The stress on the beam due to the actuation voltage is also reduced increasing the switching life time. The dynamic simulation results in switching time of 6.5 μsec compared to the 8.9 μsec of the analytical results. It can be implemented by the well established surface micromachining for RF applications.

1. Petersen, K. E., "Membrane switches on silicon," IBM J. Res. Develop., Vol. 23, No. 4, 376-385, 1979.

2. Yao, J. J. and M. F. Chang, "A surface micromachined miniature switch for telecommunications applications with signal frequencies from Dc up to 4 GHz," 8th Int. Solid-State Sensors and Actuators Eurosens. Conf., 25-29, 1995.

3. Yao, Z. J., S. Chen, S. Eshelman, and D. Deniston, "Micromachined low-loss microwave switches," IEEE J. Microelectromech. Syst., Vol. 8, No. 2, 129-134, 1999.
doi:10.1109/84.767108

4. Hah, D. and E. Yoon, "A low-voltage actuated micromachined microwave switch using torsion springs and leverage," IEEE Transaction on Microwave Theoryand Techniques, Vol. 48, No. 12, 2540-2545, 2000.
doi:10.1109/22.899010

5. Park, J. Y., G. H. Kim, K. W. Chung, and J. U. Bu, "Monolithically integrated micromachined RF MEMS capacitive switches," Sensors and. Actuators A, Vol. 89, 88-94, 2001.
doi:10.1016/S0924-4247(00)00549-5

6. Plotz, F., S. Michaelis, R. Aigner, H.-J. Timme, J. Binder, and R. Noe, "A low-voltage torsional actuator for applications in RFmicroswitches," Sensors and Actuators A, Vol. 92, 312-317, 2001.
doi:10.1016/S0924-4247(01)00589-1

7. Huang, J.-M., K. M. Liew, C. H. Wong, S. Rajendran, M. J. Tan, and A. Q. Liu, "Mechanical design and optimization of capacitive micromachined switch," Sensors and Actuators A, Vol. 93, 273-285, 2001.
doi:10.1016/S0924-4247(01)00662-8

8. Taylor, W. P. and M. G. Allen, "Integrated magnetic microrelays: Normally open, normally closed, and multi-pole devices," Transducers'97 1997 International Conf. on Solid-State Sens. Actuators, 16-19.

9. Tilmans, H. A. C., E. Fullin, H. Ziad, and M. D. J. Van De Peer, "A fully-packaged electromagnetic microrelay," MEMS'99, 17-21, 1999.

10. Rao, Q. and T. A. Denidni, "On improving impedance matching of a CPW fed lowp ermittivity dielectric resonator antenna," Progress In Electromagnetics Research, Vol. 53, 21-29, 2005.
doi:10.2528/PIER04062901

11. Peroulis, D., S. P. Pacheco, K. Sarabandi, and L. P. B. Katehi, "Electromechanical considerations in developing low-voltage RF MEMS switches," IEEE Transaction on Microwave Theoryand Techniques, Vol. 51, No. 1, 259-270, 2003.
doi:10.1109/TMTT.2002.806514

12. Chan, R., R. Lesnick, D. Becher, and M. Feng, "Low-actuation voltage RF MEMS shunt switch with cold switching lifetime of seven billion cycles," IEEE J.Microelectromech. Syst., Vol. 12, No. 5, 713-719, 2003.
doi:10.1109/JMEMS.2003.817889

13. Duffy, S., C. Bozler, S. Rabe, J. Knecht, et al. "MEMS microswitches for reconfigurable microwave circuitry," IEEE Microwave and Wireless Components Letters, Vol. 11, No. 3, 106-108, 2001.
doi:10.1109/7260.915617

14. Ulm, M., T. Walter, R. Mueller-Fiedler, and E. Kasper, "K-band capacitive MEMS â€” Switches," Silicon Monolithic Integrated Circuits in RF Systems, 26-28, 2000.

15. Barker, N. S. and G. M. Rebeiz, "Fabrication process and model for a MEMS parallel-plate capacitor above CPW line," MEMSWAVE 2004, 2004.

Dr. Saeid Afrang

Dr. Ebrahim Abbaspour-Sani